Koala-kare 876-KIT Manuel d'utilisateur télécharger pdf

Materials Supplied: Tools Needed:

Shock Flat Head Screwdriver

Step 1.

Remove the baby changing station from the wall by unscrewing the

mounting screws from the inside of the unit. Place the unit face down

on a soft material (ex: a blanket) to protect the stainless steel ﬁ nish.

Step 2.

The shock can be accessed on the back side of the station. On both

ends of the gas shock there is a “C” clip that holds the shock onto

the ball stud. To remove the gas shock carefully slide a Flat Head

screwdriver in-between the shock and the “C” clip at the top of the

shock. Once the tension on the “C” clip is removed you will be able to

pull the gas shock off the ball stud.

Step 3.

For recessed models, position the baby changing station on a

4” x 4” x 36” (102 mm x 102 mm x 914 mm) wooden block (or similar

surface) so that the trim ﬂ ange around the unit hangs over the edge

of the block without touching the surface below. For wall mounted

models stand on a blanket or other soft material to protect the

stainless steel ﬁ nish. Open the door of the baby changing station all

of the way. You should be able to locate the lower ball stud on the

bottom of the door. Use a long Flat Head screwdriver to release the C

clip on the lower ball stud, by inserting it into the shock opening.

Step 4.

Slide the thin end of the replacement shock down through the hole in

the back of the unit. Snap the replacement shock onto the lower ball

stud. Make sure the shock is secured to the ball stud by slightly twisting

the shock to make sure that it does not come unhooked.

Step 5.

Close the door of the Baby Changing Station all of the way. With

the door completely closed compress the shock so that it can be

attached to the upper ball stud. Snap the shock onto the ball stud.

Twist the shock to make sure that it does not come unattached from

the ball stud.

Step 6.

Open and close door of unit several times to make sure that the

shock is functioning properly and the door opens smoothly. Remount

unit following the proper installation instructions that were provided

with the unit. Open and close door several times after the unit has

been mounted. Close the unit after the shock has been tested.

Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399

www.koalabear.com

KB100-ST, KB110 and KB111 REPLACEMENT SHOCK INSTRUCTIONS

P/N 874-KIT-ST (KB100-ST)

P/N 875-KIT (KB110)

P/N 876-KIT (KB111)

Compress

Shock Down

P/N 1024 May 2012

BW HALFTONE

Résumé du contenu

Page 1 - P/N 876-KIT (KB111)

Materials Supplied: Tools Needed:Shock Flat Head ScrewdriverStep 1.Remove the baby changing station from the wall by unscrewing the mounting sc

Modèles reliés 875-KIT | 874-KIT-ST |

Commentaires sur ces manuels

Pas de commentaire

Koala-kare 876-KIT Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Koala-kare 876-KIT. Koala Kare 876-KIT User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 875-KIT | 874-KIT-ST |

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Koala-kare 876-KIT